Glue isn’t the first component that comes to my mind when discussing ways to make lithium-ion (Li-ion) batteries more efficient but researchers at SLAC National Accelerator Laboratory at Stanford University have proved that the glue used to bind a Li-ion battery together can make a difference to its efficiency (from the Aug. 20, 2013 news item on phys.org),

When it comes to improving the performance of lithium-ion batteries, no part should be overlooked – not even the glue that binds materials together in the cathode, researchers at SLAC and Stanford have found.

Tweaking that material, which binds lithium sulfide and carbon particles together, created a cathode that lasted five times longer than earlier designs, according to a report published last month in Chemical Science. The research results are some of the earliest supported by the Department of Energy’s Joint Center for Energy Storage Research.

“We were very impressed with how important this binder was in improving the lifetime of our experimental battery,” said Yi Cui, an associate professor at SLAC and Stanford who led the research.

The Aug. 19, 2013 SLAC news release by Mike Ross, which originated the news item, provides context for this accidental finding about glue and Li-ion batteries,

Researchers worldwide have been racing to improve lithium-ion batteries, which are one of the most promising technologies for powering increasingly popular devices such as mobile electronics and electric vehicles. In theory, using silicon and sulfur as the active elements in the batteries’ terminals, called the anode and cathode, could allow lithium-ion batteries to store up to five times more energy than today’s best versions. But finding specific forms and formulations of silicon and sulfur that will last for several thousand charge-discharge cycles during real-life use has been difficult.

Cui’s group was exploring how to create a better cathode by using lithium sulfide rather than sulfur. The lithium atoms it contains can provide the ions that shuttle between anode and cathode during the battery’s charge/discharge cycle; this in turn means the battery’s other electrode can be made from a non-lithium material, such as silicon. Unfortunately, lithium sulfide is also electrically insulating, which greatly reduces any battery’s performance. To overcome this, electrically conducting carbon particles can be mixed with the sulfide; a glue-like material – the binder – holds it all together.

Scientists in Cui’s [Yi Cui, an associate professor at SLAC and Stanford who led the research] group devised a new binder that is particularly well-suited for use with a lithium sulfide cathode ­– and that also binds strongly with intermediate polysulfide molecules that dissolve out of the cathode and diminish the battery’s storage capacity and useful lifetime.

The experimental battery using the new binder, known by the initials PVP, retained 94 percent of its original energy-storage capacity after 100 charge/discharge cycles, compared with 72 percent for cells using a conventionally-used binder, known as PVDF. After 500 cycles, the PVP battery still had 69 percent of its initial capacity.

Cui said the improvement was due to PVP’s much stronger affinity for lithium sulfide; together they formed a fine-grained lithium sulfide/carbon composite that made it easier for lithium ions to penetrate and reach all of the active material within the cathode. In contrast, the previous binder, PVDF, caused the composite to grow into large clumps, which hindered the lithium ions’ penetration and ruined the battery within 100 cycles

Even the best batteries lose some energy-storage capacity with each charge/discharge cycle. Researchers aim to reduce such losses as much as possible. Further enhancements to the PVP/lithium sulfide cathode combination will be needed to extend its lifetime to more than 1,000 cycles, but Cui said he finds it encouraging that improving the usually overlooked binder material produced such dramatic benefits.

Here’s a link to and a citation for the published paper,

Stable cycling of lithium sulfide cathodes through strong affinity with a bifunctional binder by Zhi Wei Seh, Qianfan Zhang, Weiyang Li, Guangyuan Zheng, Hongbin Yaoa, and Yi Cui. Chem. Sci., 2013,4, 3673-3677 DOI: 10.1039/C3SC51476E First published online 11 Jul 2013

There’s a note on the website stating the article is free but the instructions for accessing the article are confusing seeming to suggest you need a subscription of some sort or you need to register for the site.

I have written about Yi Cui’s work with lithium-ion batteries before including this Jan. 9, 2013 posting, How is an eggshell like a lithium-ion battery?, which also features a news release by Mike Ross.